An Easy Instruction for Installing a Bathtub
An Easy Instruction for Installing a Bathtub
Blog Article
They are making several great points about Installing A Bathtub as a whole in the article followed below.
Installing a bath tub isn't exactly brain surgery, but it does need solid plumbing, carpentry, and sometimes, tiling skills. Replacing an old tub with a brand-new one is also a reasonably difficult job. If the old bathtub is readily available, the project can relocate immediately; if you have to open a wall to eliminate the old tub and also place the brand-new tub, the task is a lot harder. In either instance, the project is within a home handyman's skills, although you will need a helper to move out the old bathtub and embeded in the brand-new one. Make certain you have actually certified yourself for the task as well as are comfortable attempting it. Instead of hiring a service provider to take over a halfway-completed task, it is better to consider using one before you begin. Opportunities are you may require an expert plumber to make tube connections.
This short article will certainly aid you install a brand-new bath tub in your bathroom if you have already acquired a brand-new bathtub and also do not require to change the plan of your previous supply of water pipes.
Your devices as well as material checklist need to make up the following:
Preparing for the Installation
Firstly, the supporting frame supplied with the bath must be fitted (if required) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is important to ensure that if the faucet includes a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is also practical to fit a supporting plate under the taps unit to prevent strain on the tub.
Fit the flexible tap connectors to the bottom of both faucets making use of 2 nuts as well as olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet via the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Ensure you use every one of the provided washers.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to now prepare to be suited its last placement.
Removing Old Taps
If you require to change old faucets with new ones as a part of your installment, then the first thing you need to do is detach the water system. After doing so, switch on the faucets to drain any type of water remaining in the system. The procedure of getting rid of the existing faucets can be quite troublesome because of the restricted access that is commonly the situation.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the faucets. Have a fabric ready for the remaining water that will originate from the pipelines. When the supply pipelines have been gotten rid of, utilize the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single faucets from turning during this procedure. When the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleansed of any type of old sealing compound.
Prior to proceeding to fit the new faucets, compare the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new taps, then a shank adapter is needed for the new taps to fit.
Setting up the Tub
Making use of the two wooden boards under its feet, position the bath tub in the required setting. The wooden boards are valuable in equally spreading out the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto 4 tiny points.
The next goal is to make certain that the tub is leveled all round. This can be accomplished by checking the spirit level and also changing the feet on the bathtub till the level reads level.
To mount taps, fit all-time low of the furthest adaptable tap port to the appropriate supply pipe by making a compression sign up with; then do the exact same for the various other tap.
Switch on the water supply as well as check all joints and also new pipework for leaks as well as tighten them if needed. Fill the tub as well as additionally check the overflow electrical outlet and also the typical electrical outlet for leakages.
Finally, take care of the bath paneling as defined in the manufacturer's user's manual. Tiling and also securing around the tub must wait till the bath tub has actually been used at least once as this will settle it into its final setting.
Suitable New Taps
If the tails of the brand-new faucets are plastic, after that you will require a plastic adapter to prevent damage to the string. One end of the port fits on the plastic tail of the faucet and also the other end offers a link to the existent supply pipelines.
If you require to fit a monobloc, after that you will certainly call for decreasing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, place the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines remain in place between the faucet and the sink. Safeguard the tap in position with the maker offered backnut. As soon as the tap is safely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical faucet adapters. The former type needs to be connected to the tap finishes initially, tightening just by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the area where the bath meets the tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the installation can move enough to fracture a stiff seal, creating the water to penetrate the wall surface in between the bathroom and also the tiling, bring about problems with dampness as well as possible leakages to the ceiling below.
You can choose from a selection of coloured sealers to blend in your fixtures and also installations. They are sold in tubes and also cartridges, and also are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger space to load, you can load it with spins of drenched paper or soft rope. Keep in mind to always fill up the bath tub with water prior to sealing, to permit the motion experienced when the bathtub is in use. The sealant can break fairly very early if you do not consider this movement before sealing.
Additionally, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also conveniently offered on the market. It is advisable to fit the ceramic tiles using waterproof or water resistant glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a keen reader about How to Install a Bathtub Yourself, I figured sharing that excerpt was a good idea. Enjoyed reading our blog? Please share it. Help other people discover it. Many thanks for your time. Visit us again soon.
Leading plumbing expertise for emergencies. Report this page